Keeprite Dc90 Manual
| Error Codes | What this means | How to fix it |
|---|---|---|
| Heartbeat LED pattern on solid | The control is locked out and will auto-reset after 1 hour. | Reset power to clear the lockout. |
| Two LED flashes | Pressure switch didn’t open. | Obstructed pressure tubing; a pressure switch that’s stuck closed. |
| Three LED flashes | The low-pressure switch did not close or has reopened. | Proper vent sizing; air leak; restricted vent; clogged condensate drain; low input gas pressure; excessive wind; improper pressure switch wiring; water in vent piping; disconnected or obstructed pressure tubing. |
| Four LED flashes | Limit circuit fault. | Loose blower wheel; defective switch or connections; improper minimum- or maximum-heat gas input adjustment; dirty filter or restricted duct system; improper limit switch. |
| Five LED flashes | Abnormal flame-proving signal. | Leaky gas valve; stuck-open gas valve. |
| Six LED flashes | Ignition proving a failure. | Low inlet gas pressure; control ground continuity; gas valve defect; defective hot surface igniter; oxide buildup on the flame sensor; inadequate flame carryover; flame sensor mustn’t be grounded. |
| Seven LED flashes | Limit circuit lockout. | Control will auto-reset after 3 hours. Refer to status code #4. |
| Eight LED flashes | Gas heating lockout. | Gas valve stuck closed on control. |
| Nine LED flashes | Medium pressure switch, high-pressure switch, or PSR relay didn’t close or was reopened. | Refer to status code #3. |
| Ten LED flashes | Polarity. | Correct line voltage polarity. |
| Status codes 1 + 2 | Blower on after power up. | Normal operation. |
| Status codes 1 + 5 | Blower motor lockout. | Control will auto-reset after 3 hours. Refer to status code #4 + 1. |
| Status codes 3 + 5 | Gas valve fault. | RED, YELLOW, or ORANGE wire at the gas valve. |
| Status codes 4 + 1 | Blower motor fault. | Blower failed to reach 250 RPM, or the blower failed to communicate within the prescribed time limits. |
| Status codes 4 + 2 | Inducer motor fault. | Proper vent sizing; restricted vent; failed inducer motor; improper motor wiring; a blockage in the tubing to the pressure switch assembly. |
| Status codes 4 + 3 | The low or medium pressure switch is open while the medium or high-pressure switch is closed. | Low inlet gas pressure; clogged condensate drain; improper pressure switch wiring; water in vent piping; low or medium pressure switch stuck open; disconnected or obstructed pressure tubing. |
| Status codes 6 + 1 | Ignition lockout. | Control will auto-reset after 3 hours. Refer to status code #6. |
Keeprite Dc90 Manual Parts
Keeprite Dc90 Furnace Manual
This manual in the following manner:! CAUTION Signal Words on Product Labeling Signal words are used in combination with colors and/or pictures or product labels. Apowermirror pc setup. The signal word WARNING is used throughout this manual in the following manner: Safety−alert symbol When you see this symbol on the unit and in instructions or manuals, be alert to the. Descargar naruto to boruto shinobi striker pc espanol.
Keeprite Dc90 Manual Rv
- Keeprite N9mp Manual - Lighter2case.wpxnews.com Keeprite N9mp Manual If you are looking for a eBook Keeprite n9mp manual kehyike in pdf plan accordingly you get befall to ethical online largest archive. Read Full Source.
- 100% OEM Parts for Every Commercial Kitchen. Shop Online and Parts Ship Today! Call us at 1-800- 458-5593.
- We found several results for Tempstar Dc90 Furnace Manual. Keeprite dc90 furnace - hvac - diy chatroom home improvement Keeprite DC90 furnace. Furnace blows cold air (thermostat set high temp). Real man shoot in manual. If it ain't grounded, it ain't dead. Tempstar furnace parts from sears.com Looks like you searched for term 'tempstar.
- 100% OEM Parts for Every Commercial Kitchen. Shop Online and Parts Ship Today! Call us at 1-800- 458-5593.